SanbilaSanbila

DaVinci Resolve: unable to generate proxy media

Resolve refuses to build your proxies and shows unable to generate proxy media. Here is what the error really means and how to fix each cause, from the most common down.

·7 min read
davinci-resolveproxyworkflowtutorial
Watch Sanbila in action

When DaVinci Resolve says it is unable to generate proxy media, it means it could not write or encode the light proxy file for one or more clips. Most of the time the cause is one of three things: the drive it writes to is full or off limits, the proxy resolution is too low for the clip, or the source file uses a codec its proxy engine chokes on. Here is how to tell which one you have, and the fix for each.

Check the destination drive and Working Folders first

Resolve writes proxies to a Proxy Generation Location set in its settings, look under Working Folders, not next to your originals. If that folder sits on a drive that is full, disconnected, or that Resolve cannot write to, generation fails before it really starts. Rule this out first, because it is both the most common cause and the quickest to check.

  1. Open Resolve settings and read the Proxy Generation Location path under Working Folders.
  2. Confirm that drive is mounted and has real free space, not a few hundred megabytes left.
  3. Check that your account can write to that folder, and that it is not a read only or network share that dropped out.
  4. Point it at a local drive with room to spare, then right click the clips and choose Generate Proxy Media again.

Try a different proxy resolution

Resolve builds proxies at a fraction of the original, such as Half or Quarter resolution, set in the proxy settings. Very small results can fail outright, and some editors have found that a clip which refuses to generate at Quarter will generate at Half. If only a few clips fail, and they are your smallest or most unusual sizes, raise the proxy resolution one step and run those clips again.

The source codec may be the problem

If the same clips fail no matter what you change, look at the source. Heavily compressed files, and variable frame rate footage straight off a phone or a screen recorder, can confuse a proxy or optimized media engine. The fix is to give Resolve something cleaner to work from: transcode the original to a constant frame rate editing codec first, or generate the proxy in a different format.

A quick test tells you where the fault is. Drop a known good ProRes or H.264 clip into a fresh project and generate a proxy from it. If that works, the problem is your source files, not Resolve.

A half made proxy that is already broken

Sometimes a proxy got half written during an earlier crash or a full disk, and Resolve keeps failing because it is tripping over that broken file. Clearing it out and starting fresh is often all it takes.

  1. Select the clips, right click, and unlink or clear the existing proxy.
  2. Delete the matching proxy files from the Proxy Generation Location on disk.
  3. Make sure there is free space, then generate the proxy media again.

Free version, Studio, and out of date builds

A few source formats decode differently in the free version and in Studio, and proxy generation can fail on a build with a known bug. If you are on the free version and only certain high end or 10 bit clips fail, that limit may be the reason. Update Resolve to the current release, or roll back if the failures started right after an update, and check the release notes for proxy fixes.

H.264 and HEVC footage

H.264 and HEVC lean on hardware decoding, and when that path is flaky on a given machine, proxy generation from those files can stall or fail while other codecs sail through. Generating the proxy in DNxHR or ProRes instead of H.264 often gets past it, and it gives you a smoother codec to edit on anyway. If you are unsure which proxy codec to pick, ProRes Proxy and DNxHR LB are the safe light choices.

The same checklist in Premiere, Final Cut and Avid

None of this is unique to Resolve. The same checklist clears failed proxy and optimized media in other editors: a destination with room and write access, a sensible proxy resolution, a clean source codec, and no half written proxy in the way. If you hit it with Premiere Pro proxies, Final Cut optimized media or Avid, work through the same four causes in the same order.

Where Sanbila fits

There is also a way to skip the local proxy engine entirely. Sanbila is desktop software with cloud storage for video editors, built so the proxies are made in the cloud rather than on your machine. You pick a proxy preset that suits Resolve, such as ProRes Proxy or DNxHR LB, and the light files come back ready to use. Resolve never has to run its own proxy generation, so this particular error does not come up.

You edit from a virtual folder that Resolve opens like any normal folder, cutting on the light proxies. When it is time to export in full quality, Smart Relink switches the clips used in your timeline to the original files streamed from the cloud. On Resolve, Final Cut and Avid this is the relink by virtual folder, not the native Premiere proxy attach.

Two honest limits. The files have to be in the cloud first, so the first import takes an upload. And Sanbila is a separate desktop app that prepares the folder you then open in Resolve, not a plugin living inside Resolve itself.

Generate your proxies in the cloud and edit in Resolve from a virtual folder. Free plan with 5 GB.

Try Sanbila free

Sources

  • Blackmagic Design, DaVinci Resolve Supported Codec List (official PDF), documents.blackmagicdesign.com
  • Blackmagic Design Forum, proxy and optimized media generation threads, forum.blackmagicdesign.com
  • Third party troubleshooting guides (Beginner's Approach, Cutsio), cross checked against the references above.

FAQ

Why does DaVinci Resolve say unable to generate proxy media?

It could not write or encode the proxy file for one or more clips. The usual reasons are a destination drive that is full or unreachable, a proxy resolution that is too low, a source codec its engine cannot handle, or a broken proxy left over from an earlier failure.

Proxy generation keeps failing, what should I check first?

The destination. Find the Proxy Generation Location in Resolve's settings and confirm that drive is mounted, has real free space, and that you can write to it. That clears the most common cause before you touch anything else.

Does this error mean my footage is corrupted?

Usually not. Test it by generating a proxy from a known good ProRes or H.264 clip in a fresh project. If that works, your originals are fine and the problem is the destination, the resolution, or a specific source codec.

Which proxy codec should I use in DaVinci Resolve?

ProRes Proxy and DNxHR LB are both light and well supported in Resolve. If H.264 proxies fail on your machine, one of those two is the first thing to switch to.

Can I avoid generating proxies locally at all?

Yes. With Sanbila the proxies are generated in the cloud and arrive ready to edit, so Resolve never runs its own proxy generation and this error does not come up. You edit from a virtual folder and relink to the originals for the final export.

Related posts

Written by Lassana Toure, Founder of Sanbila.

Last updated: